Centurylink ont to router Whether your modem warranty is active or you're leasing, we have options to help you upgrade. I'm still with Centurylink Fiber, they gave me an ONT with 1 fiber and 4 ethernet ports. Start by examining your existing ONT in most cases made by Calix. In both cases CL uses VLAN tagging. Technique is to set the VLAN tag to 201, as has been mentioned, then power cycle the ONT and router. If you choose to route it off to a public subnet on the other side of the router, like CenturyLink calls "LAN Subnetting", you will need to reserve the base address (the first static IP) and the broadcast (the last static IP) for subnetting purposes. Step 3. And while it's not power Unplug the power cables from the wall to both the ONT and Router, then wait 3-5 minutes before plugging them back in. This device will have WiFi built in (Hopefully WiFi 6). Ok, so right now the ONT is in the garage, and the router is run through a cable from the garage into the home, that a tech installed. Can't get Gold to connect, ethernet directly into ONT, have tried PPPoE with username and password, DNS mode, everything. The truth that is unlike EPON, GPON (used by most non-Cable ISPs) is vendor-specific. Setup 2. The router says that there's something wrong with the ISP DHCP server. Does that mean that most modern routers will work with CL fiber and what third party routers can you recommend? Does that also mean i wont need a modem? Hardly any routers will work. My question was what SFP module specifically would work with centurylink/quantum fiber service so that I can go directly into the back of my router, We are simply using tag 201 which is set on the Networking Setup page. When I asked the Brightspeed support about this, they said the router must have a We have fiber to our house and have one of the C4000 Modem/Router combos and a 716GE-I ONT. You ont looks nothing like this and will 99. My recommendation would be to move the CenturyLink router to the basement with the WAN port connected directly to the ONT (the device on the wall), then connect another Ethernet cable to from the router's LAN ports to the Topology 2: ONT (Ethernet cable) --- TP-Link Router. - 2 ports at the back of the unit (WAN/LAN & LAN). However, it can be put into transparent bridge mode if you want to use your own router. I would like to know if it’s possible to do the following: Connect the EdgeRouter 4 Moved into a new place with a Calix C844G ONT and a bunch of Ethernet/COAX outlets around the place. It depends on the model you have whether that works. Can I connect my own router (a Nighthawk model) directly to the ONT, or do I need to The aggregator on centurylink side (ALU 7750 or E7) is expecting to see a MAC address of the C3000 modem. You may have to restart the ont to get it to assign the pod an IP. I'm confused are you just trying to get a free wifi 6 router? Or are you just asking in case you cancel later, in which case you should own the router. 2gbps Xfinity cable to CenturyLink (Quantum) gigabit fiber. The Asus with Merlin is so reliable is crazy! This is compared to having to unplug the isp or cheap router weekly because something randomly quit working If you're going back and forth between the Centurylink router, and your TP-Link while testing, you may want to power down the ONT before giving it another try. I'm trying to use my CenturyLink modem as an extension, so I can plug in a cat5 to my TV/PS5 upstairs. To connect your own hardware to the CenturyLink ONT, your router needs to support two things: Logging into the ONT via PPPoE; VLAN tagging over the WAN port, since the ONT expects all packets between it and the router to be tagged with VLAN ID 201; PPPoE. Wait for at least a minute and then turn on the ONT as well as the new router. I am connected via 3' CAT 6 to the ONT I am using PPPoE and VLAN 201 Yes, the new ONT can no longer be configured in bridge mode, that if you already have a good router you should know from the start – BUT you can connect it to the ONT using dynamic IP mode and you will be able to use the wireless network on both the ONT and the router, obviously, having the router as far as possible from the ONT to cover as 11 votes, 25 comments. IP pass through still hit the NAT table. Just purchased the SG-1100 and am trying to configure it to my Centurylink Fiber ONT. It's not yours, it's CenturyLink's property at your house. 1. I just upgraded my Netgear router/satellite from the Orbi 850 to the Orbi 770. I have an ASUS router and it seems like you do it in the IPTV settings, I set that and BOOM, no internet connection and cannot access the modem, If I remove the VLAN tag, it works again. Has anyone with CenturyLink fiber had success in eliminating their ONT by using the SFP port on the Edgerouter 4? Thanks! Skip to main content. Both online and the tech support assured me that I needed a new router because my CenturyLink provider router (Actiontec C3000A) would not work with Quantum Fiber service. Configuration save You may want to do this before doing a modem reset to return to factory defaults, for instance. It will replace the ONT (Calix in my case). Setup 1. I have already setup pppoe settings (username, password, always on) and under vlan settings added 201. If you choose to set up a customized admin password, be sure to keep it in a safe place. I have contacted Quantum and they said to set my own router to Vlan Tag 201. Previous the router was at my house where I had no problems, only diff is that I have Xfinity. Get app Not sure if this still works but I got mine right off of their supplied router like this: In fact, I actually spoke to tech support about that last week, because the online process said I needed a new router and one would be sent to me free of charge. I was going to go from ONT -> Centurylink Router -> Ethernet Splitter -> Eero. Boot up the router. So CenturyLink came out yesterday and used the old existing modem/router, the C3000Z, and plugged it into the ONT(in the basement). Evidently, the ONT Ethernet port matters (it's not like a switch). This means you are more-or-less forced to use the ONT your provider gives you. The current config is: ONT > Orbi 1 Orbi 1 > unmanaged switch Solved: Hi; I have a CenturyLink C1000Z router/modem and wondered if the Orbi router will connect to it or if the Orbi router would have to replace × We are aware of an issue with the NETGEAR Armor and NETGEAR Smart Parental Controls (SPC) services. Centurylink's support is pretty worthless here, the first person I talked to didn't know what a NAS is, even after I described it briefly. Are you in Portland? This is my exact story until 2 days ago when it went down entirely. Can you please help me pick a router? I’m more tech savvy than the average bear, but I’m out of my depth on this one. Plug the WAN into your router and configure it for DHCP with VLAN tagging set to 201. If I plug the cable directly from ONT to Google a wifi in PPPoE mode, it doesn’t connect to the internet. I've had my router with nearly a year of uptime. From the sounds if it, it's the ONT that actually gets me on the ISPs network and that the C4000 is not really much of a modem in this setup. Depending on your router, you'll want to make sure that the VLAN is applied to the WAN or all wired ports and wireless connections. (A CL tech said they often fail after 4-5 years, and mine is that old- Topology 2: ONT (Ethernet cable) --- TP-Link Router. The CenturyLink technician showed me that internet was working fine when the ONT was connected to the ONT (looks like a router) that provides fiber-to-Ethernet at the house is Centurylink-owned and no charge. I have fiber with CenturyLink with a ONT provided by CenturyLink and one of their modem/router things. Just change the ONT/Router from Quantum to Bridge mode in advanced wan settings. ONT -> c4000 -> Google wifi Additionally, if I end up deciding that CenturyLink doesn't work for me, since I bought their modem can I just move over to Comcast or something similar? If you want to use your own router, what worked for me was to turn on transparent bridge mode on the CL/Quantum ONT/router, no VLAN tagging. I want to get rid of it but I don't want to connect in AP mode or use it as a bridge because it's $150 and the cost os just too damn high. Since this was the only person I’ve talked to there that was worth a damn I am going to just believe that and go with it. One cable will plug into the WAN port on the modem and then the other into the PoE injector. When I read up about the GigaPoint Calix 803C, it's a ONT (open network terminal) anyway and I did test connecting the Ethernet cable from 803C directly to my router which didn't work. Step 2: This seems to kill the network connection coming from the ONT into the modem, which then can't pass it through to the UDM, so I don't think this is the answer. Logged in to the ONT, and put it in to bridge mode. Calix makes an SFP based ONT called the GPON Interface Adapter. The router you add doesn't need VLAN tagging capability. In reality, how difficult would it be to turn off the Wi-Fi from their router and just connect my own? Easy to do this. This means I either run a 30ft cable from my closet to my living room to set up a router or use one of the COAX cable outlets. sadly no I haven’t been able to convert it from the ont to fiber to the router Fiber cable <-> ONT box <-> Ethernet cable <-> Modem/Router box. Follow the steps to complete your installation and get online. An Ethernet cable will connect your router to the fiber terminal (ONT), either directly or by plugging first into a wall jack and then into your router (this depends on whether the terminal is located outside or inside). Just plug router into ont and you're done. This goes to my router, which provides Internet to the rest of my network. Second, the ISP has a back door to remotely manage the router. Currently, I’m using the router/ont provided by Centurylink, but only using the ONT part. . Step 1. I They were talking about the router/modem combo that, in your case with fiber, will just use the router capabilities. But then you'll have 3 devices. You can plug the Ethernet cable from the ONT to your mesh router without needing the CL router. You can even set up “router behind router” to create a static router and use all 6 IP addresses. The ONT placed in the garage. The conduit for the line to the outside office is accessible from near the ONT, but would be inconvenient to run from the router. I thought that the reason I wouldn’t get any connection directly from the ONT was because of PPPoE but I contacted Centurylink and they stated they only use DHCP. You can currently set up a TPLink Deco directly to the ONT, since it does support PPPoE + VLAN tagging. If you want to use your own hardware bypassing CenturyLink’s modem, please follow the steps below. Frequently while downloading through Steam, other game services, Usenet, etc. At this point they'll supply you with a router that costs $10 a month to rent. centurylink. Network Address Translation (NAT) is an advanced networking setting that most people do not use. To get a router to accept the tagged packets from the Centurylink ONT, simply tag the existing VLAN on which the WAN connects to the routing logic. Having trouble with it. Just had CenturyLink fiber installed here in Seattle yesterday. Do not use the c4000lg which actually is just a router, it’s completely useless if As a result, I am using my own Synology router (RT2600ac), but I still need a ONT to convert fiber into Ethernet. Oh, before you leave each page, hit Apply. Personally, I don't want them monkeying around on my network. If you want to use your own hardware bypassing CenturyLink’s modem, please follow the steps as below. I configured my switch to give ports 1 and 2 the same VLAN ID. Would I then run UDM to Switch in the basement for all Cat6 wires in each room? -Behind living room TV I'd like to have everything hard wired so would I place another switch there? We are simply using tag 201 which is set on the Networking Setup page. It's not like AT&T where you HAVE to use their router. (ONT) and a router. I have two Centurylink modem/routers (the How can I ditch the rented router CenturyLink gave me and use my own router with CenturyLink Fiber internet? (ONT) somewhere in your house that converts the fiber optical into an ethernet cable. You would need them to replace the c5500xk with a Calix ONT to run ethernet direct to your router. I’ve tried using the PPPoe username and password, tried auto connect (can’t detect) with trying two brands of routers this is a Modem issue but I can’t for the life of me get internet to my router. The ont is probably just a gateway and the other device is a router. ) There are a few stale things the ONT sometimes remembers which may interfere and confuse things. Can I plug the Google Wifi direct into the AdTran ONT? I have tried, but it is not recognizing that there is internet connectivity. With Quantum Fiber owned by CenturyLink apparently they have new ONT/router combos which allow you to put the router in pass through mode and use your own router. I The C5500XK is a SmartNID and can act as a router. The default WAN VLAN port (usually 5) is set to route to the 4 LAN ports but is not tagged. Its simply there to creeate a ppp connection that is taggable. Reply reply I got news for you. Log in to the ONT ip. Ont's look nothing like routers and modems. I was trying to directly connect my Eero mesh router system into the ONT like I did with Cox before and it doesn’t seem to provide a live connection unless it’s relayed through the Century Link Router they left here then into my Eero device. IP with login info is on front of the ONT. Plug in a router Did you ever figure this out? I'm getting intermittent drops to 100mbps which are resolved by rebooting the router (Greenwave C4000XG). Port 1 is where the ONT plugs into. What you have above looks correct. Click save. Hello Everyone, I have a question. Called Centurylink, first line clueless, won't escalate. The current set up is a box in the wall with a Calix C844G which serves as both the router and modem. I am changing my Dads router to the Orbi RBR850 with Centrylink. (Assuming your current router supports PPPoE and VLAN). Most have a reasonable workaround for bypassing the router/gateway, bypassing the ONT to take the fiber directly into UniFi gear is technologically possible with the SFP ONT Ubiquiti makes, but I’ve never heard of an ISP allowing it. CenturyLink support (the one person I found that understood what I was trying to do) told me that I could not connect the ONT to my Netgear router because the ONT “won’t recognize that router”. No PPXXX or anything. After that the ONT restarted and the status light was a solid white light indicating it was in bridge mode. It all depends on the router that you have, below has things your router has to be able to do. As with my previous router (ASUS brand) the router doesn’t get internet. It should have a label with a model number that can be searched on the Internet and a serial number (SN) like CXNK12abcd34, which is used for authentication. Log in to the router if needed to setup. I think that you should be able to use the wireless router you currently have, set it up with the CenturyLink VLAN info, and skip any need for the ER-X. ” Any fiber-ready router, or router that can support the high speeds of fiber internet, will work. Once the CenturyLink tech has finished, disconnect the useless CenturyLink router from the ONT (optical network terminator) and bring it back to their store. I previously had my centurylink ont to an edgerouter x to my netgear orbi. Does anyone have any suggestions on finding a third party ONT that will work with Centurylink so I can send all of their equipment back? The install date is in the future, if you have the equipment already and you cancel the install, you would probably need to return it if they refund your first month of service. I connected the Ethernet from the ONT directly into my laptop. Now that PPPoE is supported, I was wondering if anyone with Centurylink (Quantum) Fiber has been able to successfully set up their Eero using PPPoE. The LAN port of the CenturyLink modem is connected to the wall. Step 1: Call CenturyLink for your PPPoE credentials. That way, Centurylink will have to come look I can connect TP-Link Router and have Dynamic IP/ VLAN 201 and router connects to Centurylink. It will run at gigabit for days then revert back. I setup a VLAN 201 tag on port 1. We live in a brand new single family home development but are going to be CenturyLink ON customers (MDU). So my question - when the modem is unplugged, what lights should I expect to see on the ONT? Should “dashboard” or “service” be lit? How can I narrow down the problem to the ONT or the modem? I ask, because I’ve tried and failed to get an old Netis router (with PPPoE) and a new Eero 6 working directly with the ONT. Remove the CenturyLink modem, and plug the Ethernet cable from ONT in the WAN port of your TP-Link router instead. I am in the same boat, updates have not solved the issue. Ok, so they made 4 jacks live now instead of the one. He then took one Ethernet line to power the Calix and then hooked up the C5500XK inside my closet where my low voltage box is via ethernet. The ONT (Optical Network Terminal) was installed in the garage. Reboot Typically, CenturyLink provides a combo ONT/router for their fiber service and they refer to as a modem. Is there any disadvantage With Quantum you just connect a cat cable from the ONT to your laptop/computer. The router that came with our Fiber subscription is the Zyxel C3000Z. This worked for a year but suddenly stopped. I have also tried changing the LAN IP Range in the CenturyLink router and connecting the UDM via DHCPnothing. Right now the ONT is connected to their router which is I was previously using my Google Wifi connected to the router CenturyLink provided so my first step was factory resetting my network. com/, and This means even routers that CAN NOT do VLAN 201 tag can work with C5500XK (since the C5500XK is doing VLAN tagging already). You will need to configure a PPPoE connection with your user/pass, and the vlan201, as well as set the WAN NIC MTU to 1492. I recently purchased a NetDuma R2 for use on my apartments CenturyLink ONT fiber network. the ONT crashes and I Aerial fiber will terminate outside at an enclosure on the side of your house, then a shorter fiber ran inside to the Ont, currently most of not all areas are using indoor ONTs so no ups just the fiber to the Ont, then cat5e standard enthernet to a router currently a c4000x on most areas. I recently moved to a new place with CenturyLink gigabit fiber service in the Portland, You can call CL support to get these, but you might also be able to extract them from your CL-provided router. A CenturyLink technician will install the SmartNID in your property by attaching it to the wall and connecting it to our fiber-optic network. Assuming vlan tagging is configured as you stated. As long as your router can handle PPPoE credentials, then you can essentially use any router of your choice with CenturyLink's gigabit Internet! The answer is yes. Let your wife know where you want the ont and where you want the router. Initial research indicates that the ONT is a modem, so all I need is a router. I returned my Centurylink 'router' after a pair of C3000Z failed, consecutively, I need some helpI have tried everything trying to get transparent bridge mode to work on my centurylink modem/router (I have DSL so I don't have an ONT and cannot simply get rid of the modem altogether). - Used the Google Home app to create a new network. Quantum does not provide a router per say it is a smart ONT that acts as a router only for hardwired devices - the way quantum does the install by default is ont is set up in regular mode which acts as a router. Under LAN, set LAN -IPTV setting. You'll get a discount on your monthly bill if you aren't using it. That's apparently just Once the ONT is hooked up to the network, it will be linked to your router through an Ethernet connection. To adapt to fiber-optic speeds, you’ll need a fiber-ready router, also called a “residential gateway. I'm currently using CenturyLink fiber. Step 2. Everything works. Also, Lumen/CenturyLink/Quantum Fiber now uses Smart NIDs (basically an ONT plus a wired router) instead of Calix ONTs. This weekend I had CenturyLink Fiber connected to the house. The Centurylink router is the device that you can pay a service fee for, buy out-right, or replace with a 3rd party router unit as long as it supports PPPoE and VLAN tagging. I'm trying to get the NAS attached to the Centurylink router (attached to a fiber modem / ONT). Im assuming that the ONT will convert the fiber cable signal to a ethernet cable that will then go to my router. I found a video about using just your own modem with a CenturyLink ONT, and the key points were that you must: I'm wondering if there is any way I can bypass the modem all together and run the fiber directly from the ONT box to my Deco router? I've attached a photo of the ONT box below. The advantage of going with CenturyLink's list of routers is that they are guaranteed to by them to be able to 716G-RI v2 has a flaw that would cause it to fail and CL is replacing them with seriously smaller ones that are only an ONT and not an ONT-Router-WiFi unit with the Router and WiFi turned off and only one working LAN So I have CenturyLink's 1 gigabit Internet. Wondering if any of you have gone through this and gotten it to work. c) Walk through the steps at http://connect. You can use both ports (you can connect 2 routers, and both would get an IP, or maybe setup dual WAN for redundancy if your own router supports this function). Manual ISP, Internet VID 201, DHCP route Microsoft, enable Multicast, disable Fast Leave, enable IGMP Snooping. Keep in mind though if you have ANY issues Centurylink will NOT trouble shoot anything that is not their equipment. Upon installation, it will work under router mode (does NAT / DHCP, Firewalletc). Eero Pro 6 - How I Bypassed the CenturyLink Fiber Modem and Plugged Directly into the ONT I'm hoping this can help someone that runs into the same issue I faced when setting up my new router. The ONT shouldn't be something you provide (I've had a different fiber provider before). The tech will take the ONT with them. Recently, CenturyLink migrated over to Quantum Fiber, so a tech came by last week and wanted to install the C5500XK box which is a router/ONT combo. I got C/L fiber a few years ago and I need to use a router that has VLAN tagging capability. I have CenturyLink Gig Fiber (940 down/up). It will keep doing vlan 201 so you do not have to change a thing on your router or the ONT for this. You must have a router that can handle it (or use CenturyLink's). I am setting up a Google Wifi mesh system. What I’ve tried: 1) replaced router (originally given a C4000BG by mistake but it had similar performance—Wifi speed fine, wired speed bad), 2) tried two different computers—both have 1Gb ethernet cards, 3) swapped all ethernet cables (tried various cat5e and cat6 cables), 4) updated router to latest firmware, 5) rebooted everything a couple times. I’ve got gigabit service from Century Link and after searching through old posts on here and some googling I’ve come to understand that I should be able to ditch the crappy modem/router supplied by CenturyLink and directly connect Interesting. Even though both Fiber and DSL operate through CenturyLink, the same routers will not work for you. g. On your own router if you have a pure ONT that is it also a router, you would indeed have to set VLaN 201 but that totally depends on what router you have how to do that. Just confirming that (like many on this thread) I was able to remove their router (a C4000XG) and just use my UDM instead (i. I already have the ASUS GT-AXE11000 router as well. CenturyLink Fiber only requires a router to connect to the ONT box for wireless coverage. This configuration means that directly connecting your computer to the modem with an ethernet cable will not give your device If possible Run directly from ONT box to UDM or UDM Pro. Make a backup of your settings to be able to roll-back to your original setup if needed. My ONT's WAN light will not stay solid and it just keeps cycling through the lights. Your router VLAN tags 201, While it works great for almost all of my devices, it doesn’t play well (at all really) with zscaler, so I need a router that works with both centurylink and zscaler I realize IF it's a centurylink issue, or issue with the ONT, I probably will need to set up 'double NAT' and use the C4000XG to receive the initial internet connection then add the ASUS to that. Centurylink has a different configeration for their modems to work with non-Centurylink routers. You will need to obtain the PPPoE login from CL, and set VLAN bridge to 201. I use a custom pfSense router with the provided C6500XK ONT. We advise you not to disable NAT unless instructed to do so by a qualified technician, as it could open your broadband modem to outside intrusion and create a security risk. Best router for Centurylink Gigabit Fiber . I use Eero 6 mesh, but my router is not going to establish a PPPoE connection if the ONT doesn't have a solid WAN light. If you have a gigabit connection with CenturyLink and you want to use your own wifi router, e. Learn how to replace an old or faulty modem from CenturyLink. Set up your new CenturyLink modem or router and activate your internet service. Essentially this is throwaway router because I would never place a router inside a closet. And it can also To connect your own hardware to the CenturyLink ONT, your router needs to support two things: Logging into the ONT via PPPoE; VLAN tagging over the WAN port, since a) Log in to your CenturyLink router and find it in the router settings. If you get static IP’s it does bypass the RG’s NAT table. 9% of the time not have a listed ip address or any login info on it. I am attempting to setup my orbi directly to the ont. Hopefully that works for you, my install came with an adtran ONT and a separate "modem"/router unit and changing my router was as simple as swapping the router out and setting up the vlan on my new unit. Then port 2 is VLAN 201 untagged. VLAN tagging, on the other hand, is used to separate different types of network traffic on the same physical connection. If that Adtran box is a combination of ONT and gateway in one you may be out of luck. Open menu Open navigation Go to Reddit Home. In the case of CenturyLink's network, all traffic between your router and the optical network terminal (ONT) needs to be tagged with Currently trying to use router TP-link AX3000. Purchase a fiber internet router. Any tips? just to chime in here. If that's not possible then run from CenturyLink modem/router in bridge mode to UDM. I know on the older modems, I was able to shut off the radio and add almost any router. ONT -> Amplifi Alien -> C4000XG (bridge mode) Set up your new CenturyLink modem or router and activate your internet service. I'll do my best to explain this as simply as I can. I was wondering if there is a different method to the madness of bridging the C4000LG modems for doing the same thing? Topology 2: ONT (Ethernet cable) --- TP-Link Router. Everything worked great with VLAN 201 tagging and the PPPoE credentials setup. That's it. What you are calliung your ont is not actually your ont. With the demise of the external AT&T ONT for the BGW320, that’s not a thing anymore. With a standard modem or gateway, you would lease or purchase the device from us, but the SmartNID is different. Unplug Ethernet from ONT. Hi r/HomeNetworking, . Currently I have 3 Orbi and 1 is placed in this closet. First, ISP supplied routers are usually garbage and limited on function or features. Topology 2: ONT (Ethernet cable) --- TP-Link Router. 1X. ONT -> CenturyLink Router (Transparent Bridge) -> Google wifi (PPPoE), I get 500/200. PPPoE authentication is used to establish a connection between your router and your internet service provider (ISP). Plug your wireless router in to the ONT via a cat cable. This means that you can use third party routers with your CenturyLink fiber service as long as they support VLAN tagging. • ONT Device for Optic Fiber • Zyxel C3510XZ-B1 Router/Modem My Zyxel Router’s Modem GUI does not reflect the guides provided on your website. It already supports VLAN tagging, with the instructions provided in the post quoted below. At that point, the ONT is similar to a media converter with GPON line sharing. I have attempted to connect a Netgear RAXE500 into this system, changing the C3000Z to transparent bridge mode, 201 tagged. I have an ORBI RBR50. Iv got the ONT plugged directly into my Netgate 6100. Operation mode: set as Wireless router mode. If you're getting 500-600 We just got centurylink quantum fiber installed and they gave us a router/modem. 168. Has anyone had any success putting in DHCP/ VLAN 201 where Firewalla connects to the I want to go from CenturyLink ONT to FWG to TP-Link managed switch (with three VLANs) and then to a ASUS AiMesh network (using it’s default Using the CL router as the only router should prove it’s the ONT if problems continue or it’s your router if problems go away. It's either just a router doing PPPoE or IPoE, or it's a router plus ONT if fiber. b) Contact CenturyLink support via chat. I have a AdTran ONT (1287835F1C) and it is connected to the CenturyLink provided router (Greenwave C4000XG). On CenturyLink (and Verizon), you can plug in your router directly if it supports PPPoE over VLAN, therefore avoiding a CL router. Shows up and downstream connections negotiated at 100mbps in the router WAN status. I've seen some posts on this sub-reddit that the router doesn't need to support VLAN tagging. My ONT is inside the house. The fiber is being run directly to the house today and ONT will be mounted and hooked up shortly thereafter. Step 2: Remove the CenturyLink modem, plug the Ethernet cable from ONT in the WAN port of your TP-Link wireless router instead. Let the ONT reboot. Im my area (Seattle) on CentLink fiber, I only use the ONT and not the CentLink router. I’m a Centurylink fiber customer who was still using the original modem/router in bridge mode in between the ONT and my Orbi router from the initial install years ago. I have eliminated my CL router, and have directly connected my Orbi to the Centurylink ONT. This device caps at WiFi 5 and has not performed well for me. Pod is plugged into ont in AP only mode and that is how they leave it. Centurylink tech checked the fiber line and good signal to the ONT. If you want to set the eero up as your gateway, you will need to connect an eero directly to the century link ONT (which had the fiber connection) to use pppoe with isp settings in eero to use vlan 201. I can't get my Orbi to work. I'm not sure about the C4000XG, however. Log into your router after it has power cycled, and check the connection, update router firmware, ect. Or is there an ONT and they are providing me with a router? Yes I don't know much about fiber but from what I understand the ONT is your "modem" per say. Apply. I hear Century Link does provide a router, though. Set your router to DHCP(probably the default) on the WAN side and everything works. Plus it limits bandwidth to 300mbps. What ports does your ONT have? You cannot split the connection coming out of the ONT, any new devices you get will need to be connected to a router first. Note that I think the eero 6 does not support Ethernet backhaul. Your Quantum Fiber Success Team also leverages the same guides online, and could not provide assistance. I wonder if latency would be better if I cut out the Centurylink Router and take the steps you did. I was lent a CL-branded C4000XG, and I followed this helpful guide to grab the credentials from its admin portal. If you get a TP-Link Deco Mesh router, then you won't need the managed switch between the CenturyLink Fiber ONT and your router. You will have to confirm with them what equipment they require and provide these days. Plugged my TP-Link router into the ONT and powered on the router. I had existing cat5e from garage to where I wanted the router. I have tried to configure the PPOE setting with the correct user name and password however no luck. I’m not aware of any POE devices regarding ont/modem that CenturyLink or Quantum provide. It will be nice if we can connect Eero directly to the ONT soon and avoid using CL's router altogether. To be clear for future visitors. Frontier here uses a Nokia ONT and since it’s an ex-AT&T area standard GPON uses 802. a mesh router or any fancy router, then this is the article for you! I wanted to share my experience setting up my home network with CenturyLink gigabit fiber connection to save others the pain, and explain why I have very mixed feelings about CenturyLink as a customer of their services. everything should come back like a champ. The technician installed a Calix ONT outside and plugged my fiber into that. No issues, none. This is more likely to be the GPON standard 1310nm/1490nm. Did a very neat job and were happy when I gave them a $ tip. CenturyLink can use a single ONT to service multiple customer modems. If you want to get the most speed out of CenturyLink’s fiber gigabit plan, then the ASUS RT-AX88U is one of the best high-speed router options. How do I find my PPPoE credentials without calling Centurylink? They are an absolute nightmare to deal with. The upgrade happened on a Monday; a local tech showed up, checked my setup (still the Calix ONT directly into the R7000), confirmed my upgrade had happened (I'm guessing Centurylink made the switch on their end and the tech needed to confirm that my equipment was able to handle the new service) by unplugging the R7000 and plugging his laptop directly into the There are many reasons I don't want to use the router built into the ONT. Whether you’re a heavy gamer or want unmatched speed, the RT-AX88U can handle My speeds afterwards: ONT -> CenturyLink Router -> Google wifi (DHCP), I get 700/800. I want to utilize a better, more modern router. My CenturyLink Technicolor C2000T modem/router is losing connectivity for a few minutes, several times each day, so I'm looking at replacing it, and I want to see if I can do better than buying one that CL sells. ONT -> C4000XG (bridge mode) -> Amplifi Alien - With this setup, when I put C4000XG in bridge mode, it disconnects from the internet completely. I swapped out their Zyxel modem with my own Asus wifi router set to DHCP and works fine. The administrator password prevents outsiders from accessing your home network settings through your modem. None of the Ethernet ports are connected. Follow the setup wizard As the title suggests, I want to use my 3pk Eero routers in 3 different rooms that have Ethernet connection to this network closet. It does require the mesh router to support PPPoE protocol and VLAN bridge (Virtual LAN). I was hoping someone with a similar set-up may be able to advise. x. If your current router works, not to old (still gets FW updates) and allows you to specify DNS settings, you could use PiHole as your DNS, an added bonus block ads and potential malware, it can use secure DNS (DNSSEC) too. Or visit the Modems/Routers main page for more information about I've had CenturyLink fiber for many years now from my Ubiquiti USG-3P and well into my UDM SE. Hey all, just got a new CenturyLink fiber modem and I am confused by the WAN/LAN1 port on the back. My existing router (Nighthawk R7000) connects fine to the ONT using ver I had to disconnect the old router from the ONT (I had been doing that previously and I'm certain that was not part of my original problem, which you have helped me Goal is to replace aging Axon C4000XG, upgrade to Firewalla Gold router with better Wifi behind that. One of the biggest complaints I've seen around the Internet over the last year or so is that it's really difficult to use the router of your choice with The setup is an ethernet cable connected from a multi-unit ONT to a CenturyLink ZyXEL C3000Z modem/router. I want to get an EdgeRouter 4 to use instead of the provided CenturyLink router. I’m so glad I found this blog. , UDM connected directly to CenturyLink's ONT). Also ensure you have received your PPoE credentials from the tech. We were discussing quantum and not centurylink. Call CenturyLink for your PPPoE credentials. I just got me CL modem/router yesterday and I plan on connecting it to a Netgear R7800 router. Now the direct connection is to the router so it’s providing Wifi to the home from the basement. Just wanted to make a post to help someone else down the line who wants to connect their Eero directly to Quantum/CenturyLink Fiber ONT to bypass their provided equipment. If it's not an ONT, and just a router, then you don't need to use their router at all, as long at your router supports VLAN tagging. I’m currently “bypassed” to my MikroTik box, the older AT&T Fiber bypass method works here also. (The lines are cut and hanging by the ONT). Note that the ER-X doesn’t have a USB port, so it won’t allow you to attach an external drive unless that has a network connection. Before unplugging the Ethernet cable from your ONT, make note of which Ethernet port is being used. 1. They were happy to do what I asked. In the settings change it to transparent bridge mode. Do I still have to order a modem or router from centurylink, or can I hook up my ORBI router directly to the Cat6 feed into the house? Topology 2: ONT (Ethernet cable) --- TP-Link Router. We no longer support this browser . Hi, getting Verizon FIOS (internet only) installed tomorrow. You will need a PoE injector that can be plugged in near your modem/router. Fiber from outside goes into ONT, then ethernet from ONT to C4000. I have Centurylink fiber 1GBs up and down when I use their router either directly or in pass though mode. Switch off the ONT, which is the point where the fiber gets converted to ethernet. Skip to main content. Getting our PPPoE credentials was the easy part. Usually a combo port would default to LAN unless a second WAN is needed. They used my cat5e and placed router where I asked. Thanks for the reply, I may give this a shot. My reading led me to believe I would need to use transparent bridging with VLAN tagging using PPOE credentials however it turns out my account is IPOE. Any help is greatly appreciated! Check your router. The other option is turn off the WiFi on the CL router as the other comment suggested. adjust your WiFi settings. (Turn off the ONT, connect the router, turn everything on. DSL needs both a modem and Default gateway is your router address, 192. I was wondering, has anyone ever successfully used a third party router with CenturyLink fiber? - Contacted CenturyLink to get my PPP credentials - Put the CenturyLink modem in Transparent Bridging - Factory Reset the Nest Wifi Router - Connected the Nest Wifi WAN port (globe) to the Ethernet 1 port on the CenturyLink Modem. They do the job, but not much more. I will assume you are asking about router ports. r/centurylink A chip A close button. e. I have no complaints about the wifi speed but the network will disconnect and reconnect a few times a day I have mine connected directly to ONT. You have to unplug the router provided by CenturyLink and add the new one using the same cables or ports that your router uses. I get 900+ upload but sometimes as low as 100+ download when connected to the UDMP without their router. This only applies if your service is IPoE and not PPPoE. Another fiber connects here and goes to the ONT. Is this modem capable of being set up with pppoe with vlan tagging so it can replace the centurylink router and connect directly to the centurylink fiber ONT? If it is capable, please indicate exactly how to do this using the latest firmware. I'm setup similar to you, with Centurylink fiber coming into an ONT, and then that going straight into my pfsense WAN. The C2000T looks like a DSL modem/router, so since I'm not DSL, I'm just using its router function. As some should know, when you are connecting a CenturyLink modem to a fiber ONT, it isn't really a modem, but a router. I recently switched from 1. This is not as old as yours, but still old hardware. As everyone here should know, when you are connecting a CenturyLink modem to a fiber ONT, it isn't really a modem, but a router. Traceroute records the route taken by a packet of data from your computer to a specified destination through the internet. That is literally just a modem. You can check this on your gateway/router settings by logging in via IP of said gateway/router.
dvbo ghl kptpg wbb gxrqy vck jeh fxdej fdbgp jkveu